Assortment of commonly used Slug-Buster® knockout punches, packaged to meet the contractor's needs. High-impact, rugged plastic carrying case.

Ball Bearing Drive Nut with 1 hex head 3/8 x 3

Includes balanced stock of replacement parts in sturdy steel cabinets.

SPECIFICATIONS Maximum Cutting Depth 8 Ga. (4 mm)

Additional Pictures of this Product

to replace a broken draw stud. Sizes given diameter x length.

SPECIFICATIONS Maximum Cutting Depth 8 Ga. (4 mm)

Additional Pictures of this Product

to replace a broken draw stud. Sizes given diameter x length.

SPECIFICATIONS Maximum Cutting Depth 8 Ga. (4 mm)

Additional Pictures of this Product

Replacement Draw Studs for Hydraulic Drivers

3/4- 3/8 draw stud is an alternative to the current combination of 3/4 x 5-3/8 draw stud (2113AA) and 3/8x 2-13/16 screw adaptor (1614SS) that’s used for smaller 1/2 punch applications.

3/4- 3/8 draw stud is an alternative to the current combination of 3/4 x 5-3/8 draw stud (2113AA) and 3/8x 2-13/16 screw adaptor (1614SS) that’s used for smaller 1/2 punch applications.

Draw Stud-3/4 x 2-1/8

Capacity 1-1/4 Punch - 16 gauge (1.5 mm) mild steel. 3/4, 1 and 1-1/8 Punches - 14 gauge (2.0 mm) mild steel. 7/8 and 1-1/2 Punches 10 gauge (3.5 mm) mild steel.

Draw Stud Replacment for use with Slug-Buster Punches, Point of Purchase packaged

Click Here for data sheet

Time saving ball bearing head punches faster than wrench method. Requires less than half the force of conventional ratchet drivers. Punches up through 10 gauge (3.5 mm) mild steel with Greenlee Standard and Slug-Buster® punches; and ...

To replace a broken draw stud. Sizes given diameter x length.

1-1/8 (28.6 mm) x 7-1/2 (190 mm)

Additional Pictures of this Product

Draw Stud-3/4 x 2-15/16

Draw Stud-3/4 x 2-15/16

Additional Pictures of this Product

Draw Stud Replacment for use with Slug-Buster Punches, Point of Purchase packaged

Click Here for data sheet

Draw Stud-3/4 x 4-1/8

Additional Pictures of this Product

To replace a broken draw stud. Sizes given diameter x length. For maximum draw stud life, Greenlee recommends the use of battery or hydraulic drivers.

3/8 (9.5 mm) x 3-1/2 (88.9 mm)

Additional ...

A safe, secure, steel fastener that taps concrete and eliminates the need for concrete inserts with their alignment problems. Use with Greenlee masonry drill set tool. Use in concrete, block and brick. Quick and easy two step ...

Corrosion resistant - All Tapcon® fasteners are protected against rust and corrosion by the exclusive Stalgard® finish. Fast - Install two or three Tapcon fasteners per minute. Simple two-step operation - drill, then drive - eliminates

Corrosion resistant - All Tapcon® fasteners are protected against rust and corrosion by the exclusive Stalgard® finish. Fast - Install two or three Tapcon fasteners per minute. Simple two-step operation - drill, then drive - eliminates

Corrosion resistant - All Tapcon® fasteners are protected against rust and corrosion by the exclusive Stalgard® finish. Fast - Install two or three Tapcon fasteners per minute. Simple two-step operation - drill, then drive - eliminates

Corrosion resistant - All Tapcon® fasteners are protected against rust and corrosion by the exclusive Stalgard® finish. Fast - Install two or three Tapcon fasteners per minute. Simple two-step operation - drill, then drive - eliminates